< How to Test Pedestal Sump Pump without Water? 6 Easy Steps

How to Test Pedestal Sump Pump without Water? 6 Easy Steps for Running Water Pump without Water

How to Test Pedestal Sump Pump without Water

Are you looking to learn how to test Pedestal Sump Pump without water? Only search if we have the perfect guide for you. There are multiple ways to test the functionality of your pump without using water.

This article provides a comprehensive overview of various testing methods that you can utilize to ensure that your pedestal sump pump is operating optimally. These techniques range from rudimentary visual inspections to more intricate testing procedures, providing you with an array of options based on your circumstances.  

This nifty little device removes water from the sump pit and directs it away from your foundation, keeping your home nice and dry. However, running a water pump without water can be challenging since it’s designed to activate only when water levels rise above a certain point.

Read more about the complete replacement process of a Pedestal Sump Pump here. Continue the Reading…

Nonetheless, it’s essential to test the pump periodically to ensure optimal performance even without water.

There’s no need to wait for a flood to test your sump pump! Regularly checking its efficiency can avoid any nasty surprises (and water damage) down the line. So let’s explore some of the ways you can put your pedestal pump to the test without needing a single drop of water.

How to Test Pedestal Sump Pump without Water: 

1. Locate the Float Switch on the Sump Pump: 

You must know that the crucial component of the sump pump is the float switch which is your key to finding out how deep the water in your sump pit is. It is often situated on the side of the pump or has a different cord linked to it.

This helpful little feature can give you valuable insights into your pump’s operation and how to replicate a high water level accurately. So before you attempt to test your sump pump without water, locate that float switch first!

2. Lift the Float Switch to Simulate a high Water Level:

The float switch will increase when the water level rises in your sump pit, triggering the pump to turn on. By manually lifting the float switch, you can simulate a high water level and test whether the pump turns on correctly.

Just be careful not to raise it too high, or you may damage the motor by causing continuous pumping. This also shows how to test pedestal sump pump manually without water

3. Listen for the Sound of the Pump Motor Running: 

Suppose your pump starts humming or buzzing when you turn it on; congratulations! This indicates that it is running correctly. However, if you don’t hear any sound, there may be an issue with the electrical connection.

Read more about the working process of the Pedestal Sump Pump here. Continue the Reading…

In this case, consult the manufacturer’s instructions or seek professional assistance. Testing a pedestal sump pump can be challenging; therefore, use a more innovative method.

4. Check to See if the Pump is Discharging Water: 

If your sump pump is connected to a discharge pipe thingy, you can see if the water’s going out. If the pump isn’t hooked up to one of those pipes, you should check if the water’s being pumped into another container.

Check to See if the Pump is Discharging Water, How to Test Pedestal Sump Pump without Water

Doing that will help confirm that the pump works correctly and remove water from the sump pit as intended. But seriously–if the pump isn’t discharging water at all? That means something might be blocking the discharge pipe, or there’s some issue with how well the pump is doing its job.

5. Let the Pump Run for a Few Minutes: 

It is always a good idea to give your new water pump a test run before you need it. That way, you can make sure it’s up to the job of keeping your basement dry. Plus, if there are any problems with the pump, you can spot them immediately. So go ahead and fire up that bad boy – remember to keep an ear out for anything unusual!  

6. Lower the Float Switch to Simulate a Low Water Level:

When the water level in your sump pit drops below a certain point, the float switch activates and turns off the pump. You can manually lower the float switch to simulate a low water level and test that the pump turns off correctly.

Just be careful not to drop it too much, or else you might cause the pump to turn off prematurely and fail to remove all the water from your sump pit.


Hopefully, you have learned how to test the pedestal sump pump without water! We understand that not everyone may be as experienced in this area as they would like.

That’s why we’ve written this helpful guide, so you can ensure that your submersible sump pump is working correctly – even if you’re not a total expert on the subject!

Thanks for taking the time to read this guide on testing a pedestal sump pump without water, and don’t hesitate to reach out to us if you have any further questions or concerns.


Top Rated Thermoplastic Pedestal Pumps.


  • Abu Bakar

    Meet Abubakar, an expert in sump pumps passionate about sharing his knowledge and helping others make informed decisions. With years of experience and in-depth research, Abubakar provides reliable reviews of well-tested products and valuable information on sump pumps to keep your home safe and dry.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top